0:00
Now what we're going to do today is we're going to come in here and work on the floor
0:04
We're going to roll all the gel coat on here. We're going to clean all this up. We need to see in a little bit
0:09
I am going to, we do have a couple of spots like here. You can see back here like this right here
0:14
We're going to need to fill these in, sand all this stuff off, tape everything off
0:20
So that way we can roll our gel coat on and put the non-skid in it
0:24
So I'm going to go around right now and put the filler into all these little holes
0:29
Once I get that filler in there then we will sand everything down tape it all off and start rolling gel coat
2:00
We've got everything leveled off. Everything is smoothed out No more little bumps or any issues inside here on the deck We got our tape line on We blown everything off with air And now what we need to do is wipe everything
2:20
down with acetone and go around and double check that we didn't miss anywhere. Like here
2:25
where I messed up the tape line with the sanding, we need to make sure that we get those all
2:29
fixed with some new tape. So that way, we've got a nice, clean tape line. I mean, you can see it
2:36
right here. I got a little bugger right there. I need to do a little. bit around here like this and make sure that that tape line is clean and then as long as that's
2:44
clean we're going to mix up our gel coat once we get that mixed up we're going to roll out on the
2:49
floor put our non-skid in it once we put the non-skid in that first coat once it tacks up we're
2:55
going to mix up some more gel coat add the non-skid into that gel coat and then roll that final coat out
3:01
with some sanding aid in it so that way it'll raise to the top that wax is what it is that'll
3:07
raise to the top and give us a nice, clean, sealed floor. We'll pull all of our tape up before everything
3:14
dries completely, and then we're going to have a very, very clean looking boat. We are waiting
3:21
on the chickens to stop, but everything's cleaned off, everything's wiped down with ascentone. We are
3:26
ready to apply. It's all clean. Got our setup over here. I need to grab these gloves. So we've got
3:32
our gloves, gel coat, M-E-K, in our sanding agent, as well as our, I'm a little. We're going to
3:37
our non-skid. So for our non-skid, we're just going to poke holes in the top like this
3:42
and that way we'll use this as a salt shaker to shake out our non-skid once we roll it on
3:49
Our first coat, we're going to shake it on, and once we shake it on, our second coat
3:54
we're going to mix it in with the gel coat. I'm going to mix this up in pints just because you
4:01
I mean, it's probably like 85, 90 degrees outside right now, so this is going to kick off pretty quick
4:07
And so I want to do just one pint. Now, the mixture for this is actually right here on our can
4:16
So here we've got one pint. So one pint of gel coat is going to be mixed with MekP at 7 cc So when it comes to adding our sanding agent well actually first we going to pour this in do one pint add our MECA roll it out and then when we do our sanding aid we going to do the same volume 50 of M and the sanding aid
4:42
So on our second coat, we're going to do seven point, or basically eight cc's of M-E-K, and then we'll do eight ccc's of the sanding aid
4:53
and then we'll mix that in there, mix it real good. We're gonna wipe the walls of the bucket down
4:58
just in case there's anything that gets stuck on the bucket because if you don't get that sanding aid
5:02
all mixed in really well, you might have one shiny side over here
5:07
and then over there it'll be a little bit duller because you didn't get the sanding aid all the way mixed in
5:12
That's why it's important to scrape the walls of the bucket whenever we mix
5:16
So let's go ahead and mix up our first batch of gel coat, roll it out, put our non-skid on
5:23
I'm gonnae. I'm going to be I'm gonna So, I'm gonnae
6:00
I'm gonnae. So, I'm going to be. I'm going to I'm going to make
7:09
I'm not going to be. I'm gonnae. I'm gonnae. I'ma-ha-ha-ha-ha. I'm going to be
7:18
I'm going to be. I'm going to Got the gel coat all over the floor
8:04
It looks a little thick right now with all of the non-skid, but half of that's going to go away anyway
8:11
I did get a little ripple here. I think it got a little dry when I put one pass on that, and it was dry
8:17
It's what that ripple there is. But it's non-skid. That's where you're going to be. standing that'll eventually wear it down and a lot of this sand will blow off in the
8:26
morning once it is fully dry but other than that she's looking pretty fresh
8:32
except for you I don't know what that is of course had to be a bug flying it right
8:44
when you roll it out while everything's wet if you want to get those nice sharp
8:48
lines like that then you need to pull the tape up everything is just tacked up next up on our agenda is going to be to put our rub rail on there
