0:00
Okay, now we want to get this out as far as possible
0:06
Let's deploy the ladder and make sure that it fits with the ladder deployed. Alright Donnie, today we got a boat here that has no trim tabs
0:19
Actually our next video we're going to put this on so just don't mind that right now
0:24
But here we've got an entire trim tab system. This boat has nothing on it right now
0:29
we gotta put it in the controller and all that stuff donnie want you open up that box and let's see what we got here
0:35
i just want to cut away from you kids it's a box in a box return it look at it damaged broken
0:51
it really is damaged though it is oh that will be all right oh that'll be all right
0:59
It's a little beat up ain't it? Oh, how pretty
1:10
These kits pretty come pretty much everything. I mean you got the brackets, the actuators are the wires for it
1:17
They make it pretty plug and play. Locker switches, both up and down
1:23
And then they both plug in. It's pretty nice for installation. You got power wire
1:30
I was going to say I don't see any I don't see any fuses on here but
1:36
kidding me? How to supply your own fuses? Yeah. Just return it. Just get rid of it
1:45
It's kind of interesting. I would have I would have a guess they would have a fuse but
1:50
wires to go up both the actuators and what we're going to do to start
1:58
these are already put on here so we'll just go ahead and put these on the back of the boat
2:08
and we will angle on the way we want to angle them so we're going to put these on like this first
2:28
we put that with a pin in it. Now, like this. What the third one
2:38
Yeah, I put this one first. Uh-huh. That goes in. Then, this right here. Yep
2:54
Now you can put this one
3:08
Now you can put this one on there
3:24
Send her butt. What's doing with your 716s? Do we're here? Okay
3:33
Start on one side. Start on one side and push it out
3:51
Start on one side and push it out. There you go, let's... there you go
3:58
Let's... there you go. Try and get out. Okay, now we want to get this out as far as possible
4:12
Let me try and get out as far to this corner as possible
4:19
Like that like that Because we also want to make sure that this does not stick down below the gun API
4:35
So I'm when it's fully retracted, it's not sticking down at all. That looks about good there
4:42
Maybe even a little lower. I don't even get it about right there. Yeah. Yeah
4:54
Let's deploy the ladder and make sure that it fits with the ladder deployed
5:05
Push down the ladder on the bottom a little bit. Like in, like you're standing on it. Yeah
5:12
Yeah, it'll be just fine there. Okay. All right. It's looking pretty good
5:26
Now, we just gotta marker up. Well, we also gotta go on the inside and make sure that..
5:33
Yeah, nothing on the back side. Ooh. Well, how's it looking? Not too good
5:41
Oh boy. So we got about... You got a tape measure? We got about two and five-eighths
5:50
Two and a half from the center of the bolt. So two and a half from the center of the bolt before we hit this plate
6:01
Oh man. Dang. That's pushing it. We only got two and a half inches from the center of the bolt down, which is right, I mean, right there
6:13
Basically on that line. That's what I was saying. It's right, right close with the bottom paint line
6:19
What about the other side? Well the other side is going to be the same
6:25
Except for we gotta take the batteries out. Alright, so, but this, where that was, it was about right here
6:35
Is that where that was? It was about right there. You sure
6:40
Well, you knew where you wanted it, go ahead. That thing on up there, boy
6:45
That ain't us. That's some last seal. Someone left down there. left down there yeah you twist it a little too there you know I mean that's pushing it
7:05
what about right what about we could probably pop a hole there because the wire's
7:09
gonna go through this center hole here but now that's that's gonna be pushing it man
7:17
Yeah, that's below. I mean, you'd angle the hole like that. Yeah
7:21
Like run the drill bit in an angle upward. There's no access below this plate in here
7:29
So what's that plate for? I'm not sure why that plate's in there, to be honest with you
7:35
Why? There used to be batteries or a pump of some sort of that
7:41
I don't know. I guess it's just for mounting stuff. Yeah, there's screw holes
7:45
Like, there used to be something in here. Maybe it's an oil tank? Oh yeah, could have had a two stroke on it before
7:51
Looks like a pretty recent repower. Yep. So we gotta go in a really aggressive angle upward to get into this cavity
8:01
And we gotta go out over as far as possible to get up in there. Now the pickle of it is over here
8:07
Getting in back behind there. So you've got the same situation with all these batteries in here. Yeah. Hmm
8:16
Looks like we ain't got no option, Donnie. We just got a sender
8:22
Send her at a very massive angle. All right, so now that we know where we're going to put this, I'm going to hold this up there
8:28
and Donnie's going to keep it straight, and then we're going to mark the pencil marks of where all of our holes are going to go
8:35
And then once we get those marked, then we're going to drill them out. But on this gel coat, we also want to use a counter sink here
8:42
So that way, once we put a hole in this. Once we put a hole in the gel coat, if you counter-sync it a little bit, it will keep the gel coat from chipping
8:54
I want something. Watch you in it. I don't know. I don't know. You mentioned it one time
9:16
I'm not going to be. Where is that at? What the chopper
9:51
It was there. It was a couple years later and then we back in
9:55
Yeah, that gets on the front of the board. We have got to get some of the floor
10:01
There's a guy. It's a lot. Wow. You want to make sure you get plenty of sealant here on the trim tab for you mount it
10:21
because you want it to ooze out to make sure that there's no way for water to get into the
10:25
haul from the trim tab. So make sure you get a nice outlet right there along with all the screws
10:32
Make sure you get sealant on all the screws when you put them in. Once you get this wire through the bracket
10:37
We want to make sure we don't forget this little rubber gasket piece. It's going to go on the backside right here
10:44
I'll stick that on there and then mount this up onto the transom
10:48
Push through all those seams. What do you mean push for all those seams
10:57
I mean the 42 that's in all those seams. Oh yeah, yeah, it'll be right
11:07
You're right. You got that simple green. Yep. Yep
11:49
So that's what I'm good for, man
12:07
That's the only conversation we had over there is peck
12:22
That's the only conversation that we had over there is peck. Alright
12:38
So we've got the controllers for the trim tab right here and I'm thinking where we got everything
12:50
set out here. I want to put it right about there. So these will be sitting like this because we've also got a power pole that's going in and
13:00
that's going to sit probably right like this. I'm going to center the controller for the power pole right here on the edge water
13:06
and then that way the trim tabs can be centered right about there
13:11
I think that's going to look nice. That way, your hand, you've got your controller here
13:15
You can hit the traps, boom, boom, boom, boom. Then whenever you're driving up there, you can hit the power pole when you get where you're going
13:24
It like we good back here to cut all this out Nothing back there we gonna cut with the saws off so we cut out for the controller
13:33
for our trim tabs. There she is. You're ready, right
13:43
You're ready. I can't even if you're sticking in the water
14:23
I guess. I guess I can go to the car. Now we've got our wire in here, so we just need to put our ends onto this wire
15:11
as well as the wire over there. Get these wires ran to the back from the front where we put our switch in
15:19
Pretty simple. Got these right here. These are both male ends. So that means that the female ends right here need to be up here in the console and these
15:32
ones in the back need to run to the back. So we'll pull these into the back, put the ends on those wires and then button everything
15:40
up and that'll be our trim tab system. We could try it out. Okay, this is going to be that going to be not that
16:22
Click. And then you get the other, yep. And click. All right. Beautiful
16:31
I'm going to be. I'm gonna So you ready
17:08
Take these. Time to you. Time now. Time to turn that battery switch on
17:22
Moment of truth. So I'll bring them up
17:40
Okay. Nice. So now we got our trim tab systems done. Pretty
17:48
Now we're ready to do this power pole, huh? Looks good. Nice and symmetrical. Mm-hmm
17:53
You know? For a couple of idiots. Come on now
